共搜索到20478条信息，每页显示10条信息，共2048页。用时：0小时0分0秒509毫秒
:铸态TB6钛合金；热变形；本构关系 中图分类号:TG146.2；TG139 文献标志码:A Hot deformation behavior and constitutive relationship of as-cast TB6 alloy LEI Li-ming, HUANG Xu, HUANG Li-jun, CAO Chun-xiao (Beijing Institute of Aeronautical Materials, Beijing 100095, China) Abstract: The hot deformation behavior of as-cast TB6 alloy was investigated by isothermal constant strain rate......
缩试样沿压缩轴方向剖开,固溶试样沿中心线剖开,机械抛光后侵蚀.金相组织观察及分析在TG3000型金相显微分析系统上进行,SEM图像分析在JEM-200CX型扫描电镜上进行,物相分析在D8型X射线衍射仪上进行. 图1 铸态TB6钛合金的原始组织 Fig.1 As-cast microstructure of TB6 titanium alloy 2 实验... of deformation-induced martensite in TB6 titanium alloy OUYANG De-lai1, 2, LU Shi-qiang1, cui xia1, li xin1, huang xu3 (1. School of Material Science and Engineering , Nanchang Hangkong University, Nanchang......
stress behavior of TB6 titanium alloy during hot compression deformation at elevated temperature YAN Fei-hao, LI Shi-kai, WANG Mei-jiao, YANG Hui (Luoyang Ship Material Research Institute, Luoyang 471039, China) Abstract: The flow stress behavior of TB6 titanium alloy during hot compression deformation was studied by thermal simulation at deformation temperature from 700 ℃ to 860......
Trans. Nonferrous Met. Soc. China 23(2013) 650-660 Influence of high-speed milling parameter on 3D surface topography and fatigue behavior of TB6 titanium alloy Chang-feng YAO, Dao-xia WU, Qi-chao.... In order to optimize the machining parameters in high-speed milling TB6 titanium alloy, experiments of high-speed milling and fatigue were conducted to investigate the effect of parameters on 3D surface......
Effects of thermohydrogen treatment on microstructures of α+β and β titanium alloy as-cast ZHAO Yong-qing(赵永庆), CAO Xing-min(曹兴民), XI Zheng-ping(奚正平) Northwest Institute for Nonferrous Metal... of titanium alloys obtained through protium treatment[J]. International Journal of Hydrogen Energy, 2002, 27(7/8): 769-774. [8] ZHANG Y, ZHANG S Q. Hydrogen characteristics of Ti26Al24V cast alloy......
TB6钛合金多重固溶时效热处理工艺研究 黄利军1,刘彬1,齐立春1,黄旭1 (1.北京航空材料研究院钛合金研究室,北京,100095) 摘要:采用扫描电镜,金相显微镜等分析方法,研究了TB6钛合金锻棒多重固溶时效热处理对显微组织,室温拉伸性能和断裂韧性的影响.结果表明:多重固溶时效热处理可以显著提高合金的塑性和断裂韧度,而对强度的影响不大.随着循环热处理次数的增多,强度,塑性,断裂韧度都是先升高达到峰值后开始下降.强度与断裂韧性均在三重固溶时效热处理时达到最高值,比常规热处理分别提高了9%与30%左右;塑性在双重热处理时达到最高值,比常规热处理提高了40%左右. 关键词:TB6钛合金; 热处理; 多重固溶时效; [全文内容正在添加中] ......
......
homogenization is fine. Key words: Ti-1023 alloy; TB6; iron segregation; big diameter titanium ingot Ti-1023钛合金中Fe元素的平衡分配常数是0.3,因此有很大的偏析倾向.在富Fe区,容易形成不含α相或α相含量很少的区域,即β斑,β斑会严重影响合金的塑性和低周疲劳寿命[1-3].因此,对于熔炼Ti-1023钛合金...] 潘 峰, 张少卿. 热处理对铸造Ti-10V-2Fe-3Al合金微观组织的影响[J]. 稀有金属, 1989, 13(2): 159-162.PAN Feng, ZHANG Shao-qing. Influence of heat treatment to as-cast Ti-10V-2Fe-3Al titanium alloy microstructure[J]. Chinese......
熔滴对TB6钛合金高周疲劳性能影响 刘德林1,刘昌奎1,黄利军2,黄旭2,王清瑞2 (1.中国航空工业失效分析中心,北京,100095;2.北京航空材料研究院钛合金研究室,北京,100095) 摘要:利用典型应力对比试验,研究了烧伤熔滴对,TB6钛合金旋转弯曲疲劳和轴向拉.拉疲劳的影响,并分析了烧伤熔滴的形貌和疲劳试样的断口特征.结果表明:熔滴处易形成富氧和富氮层脆性相,在应力作用下极易开裂成为疲劳源;另外,熔滴会导致基体组织发生变化,对基体一般产生第二类烧伤,破环试样表面的完整性,从而加速疲劳试样破坏,也会成为断裂源,显著降低其高周疲劳性能,对TB6钛合金高周疲劳有严重影响. 关键词:TB6钛合金; 烧伤熔滴; 性能; 高周疲劳; [全文内容正在添加中] ......
Corrosion behavior of as-cast Mg68Zn28Y4 alloy with I-phase SHI Fei(史 菲)1, 2, YU Yuan-chun(于元春)3, GUO Xue-feng(郭学锋)2, ZHANG Zhong-ming(张忠明)2, LI Ying-ying(李瑛颖)1 1. School of Materials...) were prepared by cast method. By simulating the environment of ocean, the alloy was eroded in 3.5% (mass fraction) NaCl for 2, 4 and 30 h. The microstructures of the samples and eroded alloys were......
