共搜索到2399条信息，每页显示10条信息，共240页。用时：0小时0分0秒498毫秒
退火温度对Nb+Ti双稳铁素体不锈钢织构的影响颜海涛1,2,毕洪运2,李鑫2,顾佳卿2,徐洲-2(1.上海市上海交通大学材料科学与工程学院2.上海市宝钢股份研究院)摘 要:利用电子背散射衍射技术(EBSD)研究了不同退火温度对Nb+Ti双稳铁素体不锈钢织构的影响.结果表明,随着退火温度的升高,α织构逐渐减弱,γ织构逐渐增强,当退火温度为920℃时,α织构基本消失,材料以γ织构为主.对再结晶织构的形成机制的探讨认为,铁素体不锈钢具有较强的γ织构归因于"定向形核"和"选择生长"共同作用的结果. 关键词......
and texture change after uniaxial compression at 430 °C of an extruded AZ31 alloy were studied. The samples were loaded following two routes insuring two initial textures of the samples ... by: with an n value of around 15. The annealing texture with grown grains is a retained hot deformation texture without emerging or strengthening other components. Abnormal grain growth......
......
of physical and mechanical characteristics of rocks is very important issue in various geotechnical projects. The characteristics are mainly influenced by the microfabric-texture features of rocks. In this research, dry unit weight, effective porosity, point load index, Schmidt rebound hardness, uniaxial compressive strength, and texture coefficient were measured with the aim of correlating......
J. Cent. South Univ. (2017) 24: 2773-2782 DOI: https://doi.org/10.1007/s11771-017-3691-6 Numerical optimization of gourd-shaped surface texture and experiment of tribological performance CHEN Ping(陈... parameters for generating the highest hydrodynamic pressure. Then the optimum parameters of the gourd-shaped surface texture were determined and the textures were processed on the stainless steel surface......
; 不同状态铜管ψ2=45°三维取向(ODF)图及主要织构取向 Fig. 8 ψ2=45° section of ODF and typical texture of different states 图9 不同状态铜管试样取向差角分布 Fig. 9 Distribution of misorientation angle of copper tube...: 20-60. [5] 王 雷, 李 凡, 蒋建清. 冷轧纯铜微观组织及织构演变的特征[J]. 理化检验, 2008, 44(8): 405-407. WANG Lei, LI Fan, JIANG Jian-qing. Microstructure and micro-texture evolution of cold rolling copper[J]. Physical Testing......
Trans. Nonferrous Met. Soc. China 25(2015) 14-21 Microstructure and texture evolution of AZ31 magnesium alloy during large strain hot rolling Fei GUO1, Ding-fei ZHANG1,2, Xu-sheng YANG1, Lu-yao... refinement is attained by dynamic recrystallization due to flow localization. The texture in middle layer of the sheet is basal texture with little change in intensity throughout the rolling process......
J. Cent. South Univ. (2017) 24: 303-310 DOI: 10.1007/s11171-017-3431-6 Friction properties of groove texture on Cr12MoV surface WANG Jing(王敬)1, 2, ZHOU Jie(周杰)1, ZHU Shan-shan(朱姗姗)1, ZHANG Jian... 400052, China Central South University Press and Springer-Verlag Berlin Heidelberg 2017 Abstract: To analyze the influence of surface texture on friction properties of Cr12MoV’, ordinary grinder......
......
Trans. Nonferrous Met. Soc. China 25(2015) 2875-2883 Effect of calcium addition on microstructure and texture modification of Mg rolled sheets Han-lin DING1, Peng ZHANG2, Guang-ping CHENG1, Shigeharu...: The mechanical properties and texture of AM60 (Mg-6.0Al-0.3Mn, mass fraction %) and ZXM200 (Mg-1.6Zn-0.5Ca- 0.2Mn) Mg alloys subjected to multi-pass hot rolling were investigated. The finer recrystallized grains......
