共搜索到13255条信息，每页显示10条信息，共1326页。用时：0小时0分0秒804毫秒
increases at the beginning and then decreases, at last increases in a smaller rate. Key words: aluminum alloys; small angle X-ray scattering; precipitation; volume fraction Al-Cu-Mg-Ag铝合金是新型可热处理强化的损伤容限型合金...相尺寸先增大后趋于稳定,其体积分数先增大后减小,最后再逐渐增大,且增大速率降低. 关键词:铝合金；小角度Ｘ散射；沉淀；体积分数 中图分类号:TG 146.2 文献标志码:A Small angle X-ray scattering study of Al-4.74Cu-0.50Mg-0.30Ag alloys during......
): 713-729. [15] WOO W, BALOGH L, UNG?R T, CHOO H, FENG Z. Grain structure and dislocation density measurements in a friction-stir welded aluminum alloy using X-ray peak profile analysis [J... Mechanical properties of underwater friction stir welded 2219 aluminum alloy LIU Hui-jie(刘会杰), ZHANG Hui-jie(张会杰), HUANG Yong-xian(黄永宪), YU Lei(于 雷) State Key Laboratory of Advanced Welding......
(10): 1-4. ( in Chinese) [2] LIN Gao-yong, ZHOU Jia, ZHENG Xiao-yan. Numerical simulation of extrusion process of X5214 aluminum alloy profile [J]. Journal of Central South University Technology, 2008... in aluminum extrusion Part I. Effect on pocket angle and volume on metal flow [J]. Journal of Materials Processing Technology, 2003, 135:189-196. [6] CHANDA T, ZHOU J, DUSZCZYK J. FEM analysis of aluminum......
Deformed texture of copper processed by equal channel angular pressing via different angle routes WU Bao-lin(武保林)1, HUANG Zhen-wei(黄震威)1, ZHANG Yu-dong(张宇东)1, 2, BAO Lei(宝 磊)1 , C. ESLING2 1... is corresponded with that of rolling deformation modes. Cold-deformed texture was investigated. The results show that the texture character in pure copper processed by ECAP is related with intersection angle (F......
a typical spectrum of aluminum alloy (Sample No. GBW02215) recorded under these gate parameters. Fig.2 Temporal profile of Cu emission at 324.75 nm from laser- induced plasma of aluminum alloy Fig.3... Quantitative analysis of impurities in aluminum alloys by laser-induced breakdown spectroscopy without internal calibration LI Hong-kun(黎洪坤), LIU Ming(刘 明), CHEN Zhi-jiang(陈志江), LI Run-hua(李润华......
structures. Prism pattern, which is used in many optical applications, was selected as a model pattern. The prism pattern is 50 ?m in pitch and 108° in the vertical angle. The overall size... in the cavity were measured at different positions in the cavity and the replication of the pattern was also measured at the same positions. The results show that the pressure or temperature profile through......
Fatigue behaviour of pre-strain 7B04-T7451 aluminum alloy JIANG Feng(姜锋)1, JIAN Hai-gen(蹇海根)1, YIN Zhi-min(尹志民)1, HE Zhen-bo(何振波)2 1. School of Materials Science and Engineering, Central South... area. Key words: 7B04-T7451 aluminum alloy; high cycle fatigue; fatigue crack growth rate; endurance limit ......
μm with an increment of 5 μm for both modifications, respectively. For the case without tooth profile modification, the range of crankshaft angle from 0° to 180° stands for the half tooth profile... J. Cent. South Univ. (2018) 25: 1717-1731 DOI: https://doi.org/10.1007/s11771-018-3863-z Mesh stiffness calculation of cycloid-pin gear pair with tooth profile modification and eccentricity error......
J. Cent. South Univ. Technol. (2010) 17: 824-829 DOI: 10.1007/s11771-010-0562-9 Load distribution model and voltage static profile of Smart Grid SUN Qiu-ye(孙秋野), LI Zhong-xu(李钟旭), YANG Jun(杨珺... load distribution model was established. Based on this model, exact expressions of feeder voltage profile with single and double DGs were derived and used to analyze the impact of DG’s location......
magnesium alloy sheets to determine the influence of the aluminum particles size and fraction on the forming efficiency and formed specimens based on the heating preparation times and profile curves, wall... J. Cent. South Univ. (2018) 25: 2085-2092 DOI: https://doi.org/10.1007/s11771-018-3898-1 Effect of aluminum particle on properties of viscous medium during warm viscous pressure bulging GAO Tie-jun......
