共搜索到18804条信息,每页显示10条信息,共1881页。用时:0小时0分0秒445毫秒
the grinding abrasion and the electrochemical corrosion with medium water. The wear phenomenon is the complex results from the wear and corrosion. 3.2 Evaluation of corrosion rate To well... approximating that of the stainless steel. Thus it can be used as wear-resistant materials with good corrosion resistance. 4 CONCLUSIONS 1) Under the same load and grinding abrasion, the wear rate......
Wear resistance of ceramic coating on AZ91 magnesium alloy by micro-arc oxidation ZHAO Hui(赵 晖)1, 2, LIU Zheng(刘 正)1, CHEN Li-jia(陈立佳)1, CHEN Ji(陈 吉) 3, HAN Zhong(韩 忠)3 1. College of Materials... the substrate. Dry sliding wear tests for the MAO coatings and AZ91 alloy were also carried out using an oscillating friction and wear tester in a ball-on-disc contact configuration. The wear resistance......
layer. With the optimized technical parameters, a clad layer with good surface quality and uniform microstructure was obtained. The microhardness of the clad layer HV0.2 is 1 080, and the wear rate... with the untreated titanium alloy, the coatings have a wear rate an order of magnitude less. The results of laser cladding of titanium alloys with NiTiSi mixed powders demonstrate that Ti5Si3, NiTi2, NiTi......
J. Cent. South Univ. Technol. (2008) 15(s1): 447-452 DOI: 10.1007/s11771-008-397-9 Mechanical model for yield strength of nanocrystalline materials under high strain rate loading ZHU Rong-tao(朱... and Engineering, Nanjing University of Technology, Nanjing 210009, China) Abstract: To understand the high strain rate deformation mechanism and determine the grain size, strain rate and porosity dependent......
of 40-200 ℃ with heating rate of 5 ℃/min. Abrasive wear behavior was examined by using an abrasive wear tester, schematically illustrated in Fig.2. Abrasive wear tests were carried out at room... Abrasive wear property of laser melting/deposited Ti2Ni/TiNi intermetallic alloy GAO Fei(高 飞), WANG Hua-Ming(王华明) Laboratory of Laser Materials Processing and Manufacturing, School of Materials......
......
for different alloys. Wear resistance of the CA alloys and the HT3 alloys is obviously worse than that of the HT1 alloys. The lowest friction coefficient and wear rate are found in the HT2 alloys, indicating... phases in bronze alloy are listed in Table 3, and β′ phase is the allotrop of β phase. Fig.4 Wear rate and friction coefficient of Cu-14%Al-X alloy under different heat-treatment states When......
little effect on wear rate for composites basedon martensite white cast iron,but wear rate ofconventional wear-resistant materials increaseslinearly in a very steep slope as the nominal stressincreases...Wear Behaviour of CTC/FeCrCSi Composite王华明,纪嘉林摘 要:<正> To bring the excellent abrasion-resistant po-tential of carbide into full play,composites......
Wear behaviors and lubrication medium of TiC/Al2O3 ceramic wire drawing dies YANG Xue-feng(杨学锋)1, DENG Jian-xin(邓建新) 2, WANG Hui(王 慧)1, ZE Xiang-bo(昃向博)1 1. Department of Mechanical... on the drawing force was investigated. The wear mechanisms of the ceramic drawing dies were investigated. Worn bore surfaces of the ceramic drawing dies were examined by scanning electron microscopy......
after 6 h nitriding with different deformation degrees 3.4.2 Wear The wear rate of specimens with different deformation degrees after nitriding for 6 and 7 h are illustrated in Fig. 10. As can be seen, no matter the nitriding time is 6 or 7 h, the wear rate of 30% deformed specimen is lower than that of the undeformed specimen. Compared with the wear rate of undeformed specimen, the wear rate......