共搜索到9335条信息，每页显示10条信息，共934页。用时：0小时0分0秒572毫秒
Article ID: 1003-6326(2005)02-0384-05 Superplastic solid state welding of steel and copper alloy based on laser quenching of steel surface ZHANG Ke-ke(张柯柯), HAN Cai-xia(韩彩霞), QUAN Shu-li(权淑丽... on the feasibility of isothermal superplastic solid state welding of steel and copper alloy, the welded surface of steel surface was ultra-fined through laser quenching, and then the welding process tests......
Kinetic Monte Carlo simulation of growth of BaTiO3 thin film via pulsed laser deposition ZHENG Xue-jun(郑学军)1, 2, YANG Bo(杨 博)1, ZHU Zhe(朱 哲)1, WU Bo(吴 波)1, MAO Yu-liang(毛宇亮)1 1. Faculty...) potential was introduced to calculate the interatomic interactions and the bonding ratio was defined to reflect the crystallinity, was developed to simulate the growth of BaTiO3 thin film via pulsed laser......
by laser solid forming YANG Hai-ou(杨海欧)1, 2, ZHANG Shu-ya(张书亚)1, 2, LIN Xin(林鑫)1, 2,HU Yun-long(胡云龙)1, 2, HUANG Wei-dong(黄卫东)1, 2 1. State Key Laboratory of Solidification Processing, Northwestern... South University Press and Springer-Verlag GmbH Germany, part of Springer Nature 2021 Abstract: A series of single track clads of Inconel 625 alloy were fabricated by laser solid forming. To achieve......
Trans. Nonferrous Met. Soc. China 22(2012) s813-s819 Process analysis of direct laser melting to fabricate layered hybrid beads Jeong-hwan JANG1, Sung-min MUN1, Tae-hyun KIM1, Young-hoon MOON1 School... hybrid beads were fabricated for the analysis of the layering effects between them. From these studies, the effects of the processing parameters, such as laser power, scan rate and scan line spacing......
by laser additive manufacturing and forging technology ZHANG Jin-liang(张金良)1, YE Jie-liang(叶界梁)1, SONG Bo(宋波)1,LI Rui-di(李瑞迪)2, SHI Yu-sheng(史玉升)1 1. State Key Laboratory of Materials Processing and Die... properties and anodic oxidation effect. Laser engineered net shaping technology has unique advantages in the integrated forming of high-performance large aircraft structural parts. The manufacturing......
. The results show that the optimal mass fraction of the CuP in the powder system is 15%. Key words: copper-based metal powder; additive; selective laser sintering; liquid phase sintering liquid volume fraction on direct laser sintering of metallic powder[J]. Mater Sci Eng A, 2004, 371(1-2): 170-177. [16]Barin I, Platzki G......
. The liquid WC comes into melt pool and reacts with liquid Fe. Just because of full reaction between particles and substrate, the pre-feeding mode was widely used in laser cladding. On the contrary, under... and forms block primary. On the other hand, the surfaces of WC particles will melt when they are heated by laser beam. After injected into the laser pool, liquid WC droplets which break away from WC......
to the limited liquid phase, showing typical sintering forming characteristics. After polishing, the microstructure of laser sintered Fe-Zn parts was captured by OM, as shown in Figure 5(b... the laser parameters. During sintering, a small amount of liquid phase formed and wetted the particles, thus promoting the rearrangement of particles and finally realizing the densification behavior [27......
composite powder with fine grains is used[13, 16]. With a further action of laser irradiation, the Cu matrix also melts to form liquid phase. Consequently, a molten pool containing both liquid phase(Co and Cu... Variation of microhardness across cross-section of laser sintered sample 4 Conclusions 1) Through the liquid phase sintering mechanism, the WC-10%Co particulate reinforced Cu matrix composite material......
energy density laser beam was focused on the current powder layer, the powders in the laser affected region could be completely melted to liquid and form a melt pool. The already solidified matrix... J. Cent. South Univ. (2021) 28: 1601-1614 DOI: https://doi.org/10.1007/s11771-021-4720-z Selective laser melted near-beta titanium alloy Ti-5Al-5Mo-5V-1Cr-1Fe:Microstructure and mechanical......
