共搜索到12253条信息，每页显示10条信息，共1226页。用时：0小时0分0秒531毫秒
Mg-2Nd alloys, the direct aging(T5) has the combined effect of work hardening and age hardening. The tensile strength of as rolled sample is raised to 276.4 MPa and the elongation is enhanced by 64... in age hardening. Key words: Mg-2Nd alloys; microstructures; mechanical properties; age hardening; work hardening 镁合金具有密度小,比强度和比刚度高,阻尼性,切削加工性好等优点.镁合金中添加稀土元素,可明显改善合金的热稳定性和室温强度,净化和改善合金的铸造性能,细化合金的显微组织......
pattern of U-beam for steels with different Ti addition 3.2 Precipitated particles The strengthening mechanisms include work hardening, solid-solute strengthening, fine-grain strengthening and second...J. Cent. South Univ. (2017) 24: 2215-2221 DOI: https://doi.org/10.1007/s11771-017-3630-6 Effect of Ti on microstructure and strengthening behavior in press hardening steels WEN Yu-hui(闻玉辉)1, ZHU Guo......
. The results show that the CP-Ti processed by severe plastic deformation still has ability for work hardening and can be strengthened again. The main reason of such strengthening probably caused by the variation of the microstructures results from the dynamic recovery occurred during further plastic deformation. Key words: commercial purity Ti; severe plastic deformation; strength; work hardening 由于具有高......
)
Abstract: The work hardening rate of pure tantalum was studied by tension test, optical microscope and TEM. The results show that the work hardening rate of pure tantalum is low. TEM analysis indicates..., which leads to low work hardening rate of pure tantalum.
Key words: tantalum; work hardening; dislocation density
area were obtained by computation of the work hardening rate θ from initial stress-stain data and introduction of the inflection point criterion of lnθ -ε curves and the minimum value criterion... The predicting model of critical strain is described by the function of εc=0.92×10-2Z0.0843.
Key words: work hardening rate; dynamic recrystallization; critical condition; TA15 titanium alloy
TA15合金是一种通用型高......TA15钛合金β区变形动态再结晶的临界条件
来源： 《中国有色金属学报2010年第8期》——欧阳德来 鲁世强 黄旭 雷力明
Quantitative analysis of work hardening and dynamic softening behaviors of Cu-6 wt pct Ag binary alloy based on true stress vs strain curvesAkihiko CHIBAInstitute for Materials Research,Tohoku University,Sendai 980-8577,Japan摘 要:The work hardening and dynamic softening behaviors of Cu-6 wt pct Ag binary alloy were studied by hot compression tests under......
Age Hardening of Rapidly-Solidified Mo-Th-B AlloysNing Yuantao Institute of Precious Metals,Kunming,China摘 要:<正> The splat foils with 30~35 μm... hardening response,especially for Mo-8Th-0.8B alloy.The precipitates associated with agehardening were identified to be ThB4(Tetragon) and Mo2B(C16,BTC).The times of reaching age hardening peak forboth......
for the formation of texture in AZ31 magnesium alloy sheet was also analyzed in detail. Key words: AZ31 magnesium alloy; texture control; cold formability; work hardening 1 Introduction Magnesium alloy sheets... and delivery between dislocations is enhanced, and finally obstacles which impeding the movement of dislocations such as fixed delivery jog and dislocation pileup are produced, thus the work hardening......
Cr8Mo2SiV钢二次硬化机理的研究迟宏宵1,2,马党参2,王昌2,陈再枝2,雍岐龙-2(1.云南省昆明市昆明理工大学材料科学与工程学院2.北京市钢铁研究总院结构材料研究所)摘 要:采用硬度计SEM,EDS,TEM和XRD研究了经深冷处理和未经深冷处理Cr8Mo2SiV钢的回火硬度,残余奥氏体含量和碳化物析出行为.结果表明,Cr8Mo2SiV钢经1030℃淬火后,二次硬化峰值硬度出现在回火温度为520℃.深冷处理能够显著减少残余奥氏体含量,进而提高二次硬化峰温度之前的回火硬度,并使二次硬化峰向低温区移动20℃......
alloy based on a new method of work hardening rate[J]. The Chinese Journal of Nonferrous Metals, 2018, 28(10): 30-37. [16] PRASAD G V, GOERDELER M, GOTTSTEIN G. Work hardening model based on multiple... on the Thermecmaster-Z thermal simulator, through analyzing the flow stress-strain curve characteristics, calculating work hardening rate, observing deformation microstructure of alloy and the deformation activation......
