共搜索到18618条信息，每页显示10条信息，共1862页。用时：0小时0分1秒129毫秒
Crystallographica Section B: Structural Science, 2019, 75(2): 227-234. [8] FERREIRA L M, REZENDE S C, SILVA A A A, et al. Microstructure and oxidation resistance of mechanically alloyed and sintered Ni-Nb and Ni...结合性能评价[J]. 上海口腔医学, 2018, 27(5): 39-43. LIU Qiang, ZHANG Yi-neng, LI Hui-jun, et al. Evaluation of bone bonding properties of domestic porous tantalum-niobium alloy materials[J]. Shanghai Stomatology......
C/mol and R is the molar gas constant of 8.314 J/(K·mol). Table 1 Values of φpc, φpc/2, φpc/2-φpc and Ipc at different scan rates 3.3 Chronoamperometry Figure 7 presents the chronoamperometric curves...; (6) where D is the diffusion coefficient in cm2/s, F is the Faraday constant of 96485 C/mol, n is the number of exchanged electrons, and c0 is the metal ion......
Jiang, HAYES P C, JAK E. Combined experimental and thermodynamic modelling investigation of the distribution of antimony and tin between phases in the Cu-Fe-O-S-Si system [J]. Calphad- Computer Coupling... and copper in equilibrium with tridymite in the Cu-Fe-O-Si system at T=1250 °C and 1300 °C (1523 K and 1573 K) [J]. Metallurgical and Materials Transactions B, 2019, 50: 229-241. [26] ROINE A. HSC chemistry......
on the selective orientation and structure of Ni electrodeposits[J]. Electrochimica Acta, 1995, 40(9): 1079-1092. [13] LIEZL S, EMMANUEL N N, KATHRYN C S, et al. Effect of aluminium on polarisation parameters...,沉积层较为疏松.图6(b)中随着沉积时间的延长,圆球形小颗粒逐渐增多,小颗粒相互连接,有的聚集成一个个小的团簇,在小团簇之间还存在着大量的空洞.在图6(c)中小圆颗粒慢慢覆盖住整个表面,颗粒发生了堆叠,沉积层变得更为致密,空洞逐渐减少.随着沉淀时间的增加,在图6(d)中沉积50 s的图中可以看出,镀层表面有类似鱼苗状的小颗粒,实际为棱锥状的细小颗粒组成,这些小颗粒沿着其箭头状顶点方向快速生长,相......
was controlled by computer system. After continuous printing, a complex-shaped green body and some cuboid samples were obtained. These green samples were dried in a vacuum drying oven at 60 °C for 5 h. Lastly, the dried samples were sintered at 1200 °C for 120 min in a vacuum furnace. The detailed sintering process would be discussed later. Subsequently, heat treatment was carried out, which was designed......
on Components, Packaging and Manufacturing Technology, 2020, 10(5): 845-857. [8] WU C P, YI D Q, WENG W, et al. Influence of alloy components on arc erosion morphology of Ag/MeO electrical contact materials... K, et al. Influence of nickel content on various characteristics of Ag/Ni contacts for electromagnetic contactors[C]// 2014 IEEE 60th Holm Conference on Electrical contacts (Holm), 2014: 1-5. [25......
and thereby generate a significant hydrostatic pressure. For instance, Ni single crystals subjected to HE yielded strongly refined microstructures with an average sub grain diameter of approximately... extrusion were examined using the Vickers hardness (VH) measurement and were observed along the directions parallel and perpendicular to the direction of extrusion, as seen in Fig. 1(c). Here, ED, RD and TD......
sinter bonding was performed in air at 250-350 °C using a preform comprising copper formate particles to form a bondline that is sustainable at high temperatures. H2 and CO generated concurrently by the pyrolysis of copper formate at 210 °C during the sinter bonding removed the native oxide and other oxides grown on bulk Cu finishes, enabling interface bonding. Moreover, Cu produced in situ......
分别为训练集和检验集内的数据总数. Step 2 对训练集SL和检验集ST中的输入变量根据式(4)进行标准化处理,式中的和均是基于训练数据SL的统计变量.标准化处理后的训练集和检验集分别记为: (8) (9) Step 3 基于标准化处理后的训练集,运用文献[21]中方法确定ε-SVM模型的3个元参数(即高斯核函数参数p,不敏感参数ε和正则化参数C)并训练ε-SVM模型. Step 4 利用标准化...变量平均值即,启动阴极铜产量软测量模型估算前1 h内的阴极铜产量,计算,输出并存储各类能源消耗量,单位产品能耗等指标. Step 2(b) 若电解槽在前1 h处于第一出铜期(S1)或第二出铜期(S2),考虑到该阶段没有电解反应发生,仅计算各类能源消耗量,不计算单位产品能耗. Step 2(c) 若电解槽在前1 h内经历多个作业阶段(如既有阴极周期P1又有出铜期S1),则计算单位产品能耗时仅考虑阴极......
high temperature corrosion of HVAF-sprayed Ni-based alumina and chromia forming coatings[J]. Corrosion Science, 2018, 132: 170-184. [11] NI L Y, LIU C, HUANG H, et al. Thermal cycling behavior of thermal..., 赵 齐. 钇在Fe-Cr-Al合金1200 ℃氧化中的作用[J]. 中国腐蚀与防护学报, 1982, 2(2): 35-41, 69-70. YIN Yao-de, LUO Ji-xun, ZHAO Qi. The effect of yttrium addition on the oxidation of the Fe-Cr-Al alloy at 1200 ℃[J]. Journal......
