简介概要

铝型材挤出速度对模具磨损程度的影响

来源期刊:中国有色金属学报2007年第9期

论文作者:彭必友 殷国富 傅建 蔡鹏

文章页码:1453 - 1453

关键词:铝型材;挤出速度;磨损;Archard;数值模拟

Key words:aluminum profile; extrusion velocity; wear; Archard; numerical simulation

摘    要:基于修正的Archard磨损理论,利用数值模拟技术分析挤压成形阶段模具各个测量点的瞬时温度、压力和速度场的分布,研究挤出速度对模具磨损程度的影响。结果表明:随着铝型材挤出速度的增加,模具各个测量点的磨损量都随之增加;由于模具工作带入口的正压力和温度均较其他部位大,使其磨损量也是最大的,故成为模具失效的主要区域;整个挤压过程有5 000个阶段,当挤出速度为10 m/min时,P15点的总磨损量为1.45 mm,计算结果与实际情况基本吻合,为挤压工艺的制定提供了理论依据和参考。

Abstract: Based on modified Archard’s wear theory, a lot of usefu1 data were obtained by finite element software during the process of extrusion, including instantaneous temperature, pressure and velocity field of every node, and rules of wear amount under various extrusion velocities were obtained. The results indicate that with the increase of extrusion velocity, the wear amount of each measure point increases. Because normal pressure and temperature around the die land are higher, and wear amount is also higher than the other part of the die, the die land becomes main area of invalidation. If total amount of forming phase is 5 000 and the speed is 10 m/min, the total wear amount of P15 is 1.45 mm. All the results are in good agreement with actual conditions, therefore it provides theory basis and reference to make aluminum profile extrusion process.

基金信息:国家自然科学基金资助项目
四川省科技厅应用基础资助项目



详情信息展示

[10] 王雷刚, 黄 瑶, 孙宪萍, 刘全坤. 基于修正Archard磨损理论的挤压模具磨损分析[J] . 润滑与密封, 2006, 3: 10?12.
WANG Lei-gang, HUANG Yao, SUN Xian-ping, LIU Quan-kun. Wear analysis of extrusion die based on Archard’s theory[J]. Lubrication Engineering, 2006, 3: 10?12.

[11] 黄 瑶, 孙宪平, 王雷刚, 刘全坤. 基于BP神经网络的挤压模具磨损预测[J]. 塑性工程学报, 2006, 13(2): 64?66.
HUANG Yao, SUN Xian-ping, WANG Lei-gang, LIU Quan-kun. Wear prediction of extrusion die based on BP neutral networks[J]. Journal of Plasticity Engineering, 2006, 13(2): 64?66.

[12] Langkruis J, Koo W H, van der Zwaag S. Assessment of constitutive equation in modeling the hot deformability of some overaged A1-Mg-Si alloys with varying solute content[J]. Mater Sci Eng A, 1999, 266: 135?145.

[13] Lee R S, Jou J L. Application of numerical simulation for wear analysis of warm forging die[J]. Journal of Materials Processing Technology, 2003, 140: 43?48.

[14] Snape G, Clift S, Bramley A. Parametric sensitivity analyses for FEA of hot steel forging[J]. Journal of Materials Processing Technology, 2002(125/126): 353?360

[15] Yang D Y, Lee N K, Yoon J H. A three-dimensional rigid-plastic finite element analysis of spur gear forging using the modular remeshing technique[J]. Proc Instn Mech Engrs, 1991, 205: 111?121.

                                 

基金项目:国家自然科学基金资助项目(50275100);四川省科技厅应用基础资助项目(0021780)

收稿日期:2007-01-04;修订日期:2007-06-29

通讯作者:彭必友, 博士研究生;电话:028-81783296; E-mail: randypeng@126.com

(编辑 李向群)

有色金属在线官网  |   会议  |   在线投稿  |   购买纸书  |   科技图书馆

中南大学出版社 主办 版权声明   电话:0731-88830515 88830516   传真:0731-88710482   Email:administrator@cnnmol.com

互联网出版许可证:新出网证(湘)字005号   湘ICP备09001153号